I found a cool new local website!

Hi, guys I found a new local website!  Please take a look at it Here:  http://www.mardigrasri.com

DIY Home Painting

DIY house painting is a can be a messy job, even for the best and most seasoned professional painters. Painting is something that you have to be properly set up for. You have to devise a plan of action.
Here are some very basic painting tips. Any wall repairs after sanding should be primed, the primer has the effect of sealing the repair mark so it does not flash through the finish coat as a dull spot. Another reason to use primer is if you have a dark color it will hide the dark color at a lesser cost in material. On the other hand, if you want to paint a dark color then a dark tinted primer will make a good first coat.
Invest a couple dollars for a wooden broom handle that has a screw end on it so you can screw your paint roller handle onto it. Now it is easier to dip the roller into the tray and then paint the wall from ceiling to floor without using a chair or a ladder.
Write down somewhere the color code of the paint that you used and the actual paint and paint company that you used on this wall of a room for future reference in case you need to repaint something in our room. It’s a lot easier to go in with the code for the paint than it is to go in with a piece of the paint to get matched again.
Your painting tools are very important if you buy a cheap brush you’ll most certainly get a cheap finish. Those nylon inexpensive brushes leave paint lines in your brushwork and are very hard to edge with leaving irregular finish. Higher quality brushes, of course, cost more but you’re getting a quality paint finish also. If you’re investing a lot of time into painting a room you should spend the extra few dollars on a good quality brush. Paint rollers are also important, consider the fiber pile on the roller try not to use a very thin pile on the roller because this will definitely leave inconsistent looking painting on your walls. The smallest pile to use on painting walls is half an inch. Keep your roller wet all the time don’t work it until it is dry.

2016-12-01_1847

Is it already Monday Again!

Everyone, I can not believe that it is already Monday!  Please have a good week and thanks for following us!

How to Repair a Roof

The time has come for you to fix your roof. What now? If you are not sure how to repair a roof, you can always call a contractor, and often this is the best option. However, if your home has asphalt shingles and a low slope without a lot of rooflines, you may be able to successfully tackle the job yourself.
If you have a more specialized roofing material like slate or shakes and the slope is at a sharp angle, it might be best to contract the project. Roofing is not for the faint of heart, so if heights are a dizzying concern, this is a very good reason not to go it alone. Otherwise, pick a weekend of good weather and get the job!
If you have looked at the rake, or sloping edge, and determined that you have reached your legal limit for the number of layers, then the first step in how to repair a roof is removing the old asphalt. The standard number is the original layer plus two but check with your town laws before you begin.
The bottom line here is that this is only good, old-fashioned hard work! But before you take the cat’s paw and crow bar on the roof you should check the attic. What you are looking for are rotten spots and separations in and around the sheathing. This is the plywood that forms the foundation for the roofing.
The next step in how to repair a roof is the actual removal phase. This is labor intensive and can cause quite a mess. It is advised that you rent a dumpster type receptacle to minimize the debris you will have to clean up when you climb down off the ladder. You may likewise need to utilize drop garments on finishing.
Material nails wreak destruction with garden cutters and vehicles tires. Additionally, utilize care while expelling old shingles from around glimmering.
Carefully remove the old flashing, and you can use these as templates for the new ones you are replacing them with.
During your repairs, you cannot simply nail down a new board. In all the advice on how to repair a roof, you will see that it is imperative to make the surface even. For example, if you may have an older house the plywood is likely to be 7/8″ or one inch thick. The “one-inch” plywood of today is ” thick.
This may not seem like a huge variation, but it is one that you will notice once the asphalt is laid. You may need to use extra felt in these areas to bring the surfaces flush. With these how to repair a roof initial steps you can complete this job to your satisfaction.